When water stains show up on your ceiling, the culprit is often failed flashing, not the shingles. Our flashing repair Weatherford TX crews find the breach, seal it, and test it before we leave. We handle chimney, valley, and pipe boot leaks on asphalt shingles, metal, and flat roofs across Weatherford, Texas. One call gets a roofer on your roof.
Flashing repair Weatherford TX is the trade of resealing, re-securing, or replacing the metal and membrane strips that keep water out of roof joints. Flashing sits at every transition: chimneys, sidewalls, valleys, skylights, vent pipes, and drip edge. When those strips pull loose, rust through, or get nailed wrong, water runs straight into your attic. We pull the old material, check the underlayment beneath it, and rebuild the joint with new flashing, roof cement, and proper fasteners. Most repairs take two to four hours.
North Texas weather is hard on flashing. Summer attic temps push 140 degrees, then a spring hailstorm hits and dents the metal. Wind-driven rain finds every lifted edge. If you have been searching for flashing repair Weatherford TX near me after a storm, you are not alone. We see the same pattern every spring: granule loss on south-facing shingles, then a flashing failure at the chimney two weeks later. A $300 repair now beats a $4,000 deck replacement in August.
Every flashing repair we do covers the full joint, not just the visible failure. Here is what is included in a standard visit, and what we quote separately if we find it.
We check every flashing point on the roof, not just the one you called about. Chimney, sidewall, valley, pipe boots, skylights, and drip edge all get looked at. Most leaks we find are not where the homeowner thought they were. The inspection is included in every visit.
We pull the old flashing, roofing cement, and any damaged underlayment with a shingle ripper and pry bar. Leaving old material in place is how cheap repairs fail in a year. Removal and disposal are included in the quoted price.
We install new metal flashing matched to your roof system, plus ice and water shield at valleys and sidewalls. Sealant is roofing cement rated for Texas heat. Fasteners are set with a roofing nail gun and hand-checked. Materials are included in the quote.
Before we leave, we run a controlled water test on the repaired joint and check the attic side for any remaining drip. If water is still getting through, we stay and find it. This step is included on every job, no exceptions.
We clean the gutters of debris, sweep the ground for nails, and hand you the written workmanship warranty before we drive off. You get photos of the finished work by text or email. Cleanup and warranty paperwork are part of the service.
You call and describe what you are seeing: a ceiling stain, a drip in the attic, water around the chimney. We ask the questions that narrow down the source, then book a same-day or next-morning visit. Most calls are answered by a roofer, not a call center. You get a two-hour arrival window and a text when we are on the way.
A technician walks the roof with a roofing ladder and safety harness, checking every flashing joint: chimney, sidewall, valley, pipe boots, and drip edge. We photograph the failure points and check the attic side for water tracking. The inspection takes 30 to 45 minutes on a typical single-story home. You get photos and a plain-English explanation before any work starts.
We price the repair on the spot. Most flashing jobs land between $250 and $850 depending on how many joints are involved and whether underlayment needs replacing. You get one number, no pressure, and no surprise add-ons. If the damage is bigger than flashing, we tell you that too and quote the full scope.
We remove the failed flashing with a shingle ripper and pry bar, inspect the underlayment, then install new metal, ice and water shield where needed, and seal with roofing cement rated for Texas heat. Fasteners are set with a roofing nail gun and hand-checked. Most repairs take two to four hours. We clean the gutters of debris before we leave.
Before we pack up, we run a controlled water test on the repaired joint and check the attic for any remaining drip. You get a walkthrough of what we fixed, photos of the finished work, and the warranty terms in writing. If anything is still wet, we stay until it is dry. That is the whole job.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Sets flashing fasteners to consistent depth so metal sits flat and seals properly. Hand-nailing flashing is how joints work loose in a year.
Lifts shingles and flashing without tearing the surrounding course. Clean removal is what lets us reuse existing shingles when the damage is localized.
Applies sealant in a controlled bead at every joint. We use cement rated for high-heat Texas attics, not general-purpose caulk.
Gets our technicians onto steep and multi-story roofs safely. Every crew member is OSHA-certified on fall protection.
Marks flashing cuts and alignment before we install. Precise cuts mean fewer seams and fewer places for water to enter.
Trims membrane and underlayment and sets hand-checked fasteners at corners and edges where nail guns cannot reach.
A 1925 bungalow had a ceiling stain that grew every rain. Two prior roofers had patched the chimney with cement, and the patch had cracked. The counterflashing was rusted through and water was running down the chimney chase into the attic.
We removed the old cement and rusted metal, installed new counterflashing and base flashing, and added ice and water shield at the joint. The repair took three hours and cost $680. The ceiling stain stopped spreading within a day.
A 2005 build had a small drip in the attic around a plumbing vent. The original neoprene boot had cracked from UV exposure. The homeowner had not noticed until a ceiling stain appeared after a heavy spring rain.
We replaced the cracked boot with a new UV-rated collar, resealed the base, and checked the surrounding shingles. The job took two hours and cost $295. No drip after the next storm.
A 1978 rental had a persistent leak that showed up on the ceiling far from the actual entry point. The valley metal was open at the seams and the underlayment beneath it was worn through. Two previous patch jobs had failed within a year.
We opened the valley, replaced the underlayment with ice and water shield, and installed new valley metal tied into the surrounding courses. The repair took five hours and cost $840. No leak through the following rainy season.
These are the calls we get most often from Parker County homeowners. If any of these sound familiar, we can help.
Ask a pro →We trace the stain back to the entry point, usually a chimney or sidewall flashing failure, and rebuild the joint with new metal and underlayment. Most customers see the stain stop spreading within 24 hours of the repair.
We replace the damaged counterflashing, reseal the base flashing, and check the chimney cap. If the storm also took shingles nearby, we handle that in the same visit so you are not calling twice.
We replace the pipe boot with a new neoprene or silicone collar rated for UV exposure, reseal the base, and check the surrounding shingles. This is usually a same-day fix under $350.
We open the valley, replace the underlayment with ice and water shield, and install new valley metal tied into the surrounding courses. This is a bigger job, but it stops a leak that would otherwise keep coming back.
$250 - $850 depending on scope
Flashing repair in Weatherford runs $250 to $850 for most jobs in 2026. The price depends on how many joints are involved, whether underlayment needs replacing, and how accessible the roof is. A single pipe boot reseal is on the low end. A chimney or valley rebuild with new underlayment lands higher. We quote the exact number on-site before any work starts, and the number does not change. If you have been looking for affordable flashing repair in Weatherford, this is how we keep it honest.
A $400 flashing repair now prevents a $4,000 deck and ceiling repair later. That math is the whole reason we push homeowners to fix flashing early instead of waiting for the stain to spread.
One failed pipe boot is a small job. A chimney plus two sidewalls plus a valley is a bigger one. We price per joint, so you only pay for what actually needs fixing.
If the underlayment beneath the flashing is still sound, we reuse it. If it is worn through, we replace it with ice and water shield. That adds material and labor but prevents a repeat leak.
Steep pitches and multi-story roofs take longer and require more safety setup. A single-story 4/12 pitch is faster than a two-story 10/12. We quote based on what we see on the roof, not a flat rate.
Matching existing flashing to your shingle system matters. GAF, Owens Corning, and CertainTeed systems use different details. We price the correct material for your roof, not a generic substitute.
“We had a ceiling stain that kept growing every time it rained. Two other roofers told us we needed a full replacement. These guys found the actual problem in 20 minutes: the chimney flashing had pulled loose. They fixed it the same afternoon for under $500. Six months later, still dry. That is the whole review.”
Marcus T.Homeowner, Historic Downtown
✓ Verified“After the April hail, we had water coming in around a vent pipe. I called at 9 a.m. and they were on the roof by 2 p.m. the same day. They replaced the pipe boot, resealed two other joints they found while up there, and cleaned out the gutters. Fair price, no upsell, and they showed me photos of everything.”
Sandra K.Homeowner, Austin Heights
✓ Verified“I manage six rental homes in Weatherford and use these guys for every flashing call. They give me one number, they show up when they say, and the work holds. Last winter they fixed a valley leak on a 1970s build that two other companies had missed. I have not had a callback on any of their repairs.”
Dale R.Property Manager, University Hills
✓ VerifiedMost flashing repairs in Weatherford run $250 to $850 in 2026, depending on how many joints are involved. A single pipe boot reseal is on the low end. A chimney or valley rebuild with new underlayment lands higher. We quote the exact number on-site before any work starts, and there are no surprise add-ons.
Weatherford Roofing Pros handles roof flashing fixing in Weatherford TX, including chimney, sidewall, valley, skylight, and pipe boot repairs. We have been serving Parker County since 2022 and carry GAF Master Elite and Owens Corning Preferred credentials. Call +1 817-901-5355 and we will book a same-day or next-morning inspection.
Yes. We hold same-day slots for active leaks most weekdays and run 24/7 emergency response for storm damage. Call before noon and we can usually have a crew on your roof that afternoon. If the roof is still wet, we tarp it first and return when it is safe to work.
The three most common causes here are hail damage that dents and lifts metal, thermal expansion that pulls fasteners loose in 140-degree attics, and poor installation where flashing was nailed instead of sealed. Rust and failed roofing cement are close behind. We inspect all four on every call and fix the root cause, not just the symptom.
Roof Leak RepairFlashing failure is the number one cause of roof leaks we find in Weatherford. If water is showing up inside and you are not sure where it is entering, our roof leak repair service traces it to the source and fixes it. We handle everything from a single drip to multiple entry points after a storm.Explore →
Shingle RepairFlashing and shingles work together. When we replace flashing, we often find cracked or lifted shingles around the joint that need attention too. Our shingle repair service matches your existing GAF, Owens Corning, or CertainTeed shingles so the repair blends in and the seal holds.Explore →
Missing Shingle RepairMissing shingles expose the underlayment and flashing beneath them. If a storm took shingles off your roof, the flashing at the nearest joint is usually compromised too. We replace the missing shingles and inspect every nearby flashing point in the same visit, so you are not calling us back next month.Explore →
Roof Patch RepairWhen damage is localized but bigger than a single flashing joint, a roof patch may be the right call. We cut out the damaged section, replace underlayment and flashing, and tie the new material into the existing roof. Patches are a cost-effective middle ground between a small repair and a full replacement.Explore →We answer the phone, show up when we say we will, and fix the leak the first time. Same-day slots are available most weekdays, and 24/7 emergency response is on call for active leaks. Call +1 817-901-5355 and let us get a roofer on your roof today.
Book Same-Day Repair +18179015355 →Call or text us at +18179015355 any time. We answer 24/7 for emergencies and book standard repairs Monday through Friday. Tell us what you are seeing and we will get you a time, often the same day. You can also email info@weatherfordroofingpros.com and we will reply within a few hours.